Hi guys in this article we learn some important MCQ's on subject Metrology and quality control multiple choice questions and answers so without wasting of time let's discuss,
Metrology and Quality control Multiple choice questions with Answers
Metrology and quality control multiple choice questions and answers
Q.no 1. What is quality control
A : Process recognition of entire manufacturing process
B : Concerned with the integration of all the efforts in organisation
C : Detection of defects in a product
D : Minimization of material level
Answer:- (C)
Q.no 2. Which of following is used to make optical flats
A : Toughened glass
B : Glass wool
C : Fused quartz
D : Porous glass
Answer:- (C)
Q.no 3. The following used to check the diameters of holes
A : Plug gauge
B : Ring gauge
C : Slip gauge
D : Standard screw pitch gauge
Answer:- (A)
Q.no 4. In present day measurement systems
A : direct methods are commonly used
B : one of direst methods is limited but indirect methods are commonly used
C : both direct and indirect methods are commonly used
D : all of the above
Answer:- (B)
Q.no 5. Which of following is not name of major diameter of
external thread
A : Outside diameter
B : Crest diameter
C : Full diameter
D : Cone diameter
Answer:- (D)
Q.no 6. Ability which measuring device detect small differences in quantity measured by, called its
A : Damping
B : Sensitivity
C : Accuracy
D : None of the above
Answer:- (B)
Q.no 7. The amount by which the actual size of shaft is less than actual size
of mating hole in an assembly
A : Clearance
B : Interference
C : Allowance
D : None of the above
Answer:- (B)
Q.no 8. What is order of magnification in flow type pneumatic gauge?
A : 100 to 1000 times
B : 500 to 5000 times
C : 50 to 500 times
D : 100 to 2000 times
Answer:- (B)
Q.no 9. In Angle measurement 1 degree
A : 60 min
B : 30 min
C : 60 sec
D : 30 sec
Answer:- (A)
Q.no 10. Who among following suggested seven quality tools in controlling quality
A : Juran
B : Kaoru Ishikawa
C : Dr. W. Edward Deming
D : Feigenbaum
Answer:- (B)
Q.no 11. Which of the following true for multiple start screw threads
A : produced by a single helical groove
B : Grooves should be different in spacing
C : It gives a quick transverse
D : It is formed in a transverse section on a cylinders
Answer:- (C)
Q.no 12. Malcolm Baldrige quality award for (MBNQA)
A : Total Quality Managemnet
B : International Standard Organisation
C : Total Productive Management
D : Total Quality Management
Answer:- (A)
Q.no 13. The following is line standard of measurement
A : Measuring tape
B : Slip gauge
C : Micrometer
D : End bars
Answer:- (A)
Q.no 14.The following is not used to measure angles
A : Bevel protectors
B : Calibrated levels
C : Clinometers
D : Optical flats
Answer:- (D)
Q.no 15.The thickness of light gauge sheet steel can be best checked with a
A : Finely divided steel scale
B : Depth gauge
C : Hermaphrodite caliper
D : Micrometer
Answer:- (D)
Q.no 16. What is principle of Johansson Mikrokator’?
A : Button spinning on loop string
B : Principle of interference
C : Optical magnification
D : Principle of transformer
Answer:- (A)
Q.no 17. How many divisions are graduated on thimble?
A : 20
B : 25
C : 45
D : 50
Answer:- (D)
Q.no 18. Which of following true for Pneumatic sensitivity in the pneumatic comparators?
A : Directly proportional to operating pressure
B : Inversely proportion to operating pressure
C : Directly proportional to geometrical area of orifice
D : Independent of area of orifice and operating pressure
Answer:- (A)
Q.no 19. Positive allowance will always result in a _____ fit.
A : Clearance
B : Interference
C : Allowance
D : None of the above
Answer:- (A)
Q.no 20. The following is internationally recognized and accepted unit system in
A : MKS
B : FPS
C : SI
D : All of the above
Answer:- (C)
Q.no 21.Which of the following statements is/are true according to Deming'se deadly Diseases
A : short term profits are very useful for long term goals
B : mobility of management leads to stability
C : merit rating leads to devastating
D : all of the above
Answer:- (C)
Q.no 22. An objective of quality circle team is to ______ errors and _______ quality.
A : reduce, enhance
B : increase, enhance
C : reduce, demean
D : increase, demean
Answer:- (A)
Q.no 23.Following is the theoretical size which is common to both the parts of a
mating pair
A : Normal size
B : Actual size
C : Base size
D : All of the above
Answer:- (C)
Q.no 24. Circular scale micrometer marked on
A : anvil
B : barrel
C : thimble
D : ratchet
Answer:- (C)
Q.no 25. What are responsibilities of management in the quality system
management
A : Frequently change responsibilities of employees for flexibility
B : Frequently change authorities for flexibility
C : Authority changes but fixed responsibility
D : Fix authority and responsibility
Answer:- (D)
Q.no 26. The frequency distribution of numerical data can graphically represented by a ______
A : Histogram
B : Plan Do Study Act
C : Scatter Diagram
D : Fishbone Diagram
Answer:- (A)
Q.no 27. What is effect of improper alignment each tooth
A : Tooth thickness increases
B : Face width decreases
C : Load will not distributed evenly
D : Pitch of teeth reduced
Answer:- (C)
Q.no 28. Which of following not true about axial thickness of screw thread
A : Measured in direction perpendicular to the axis of thread
B : Measured on pitch cylinder
C : Distance between opposite faces of same thread
D : Measured at the same thread
Answer:- (A)
Q.no 29. What is meant P, D, S and A in PDSA cycle
A : Progress Development Study Act
B : Plan Do Study Act
C : Project Development Study Act
D : Prevention Do Study Act
Answer:- (B)
Q.no 30. Scatter diagram is graphical component of ____________
A : Regression analysis
B : Demand
C : Supply
D : Profit
Ans:- (A)
So in this article we learned Metrology and quality control multiple choice questions and answers hope you understand well.
Thanks for reading. Any query comment below.
.jpg)
